Technical data

Only with Danfoss frequency converter

Frequency converter:

Electrical connection
Operating voltage	3 x 380 – 480 V ± 10 %
Mains frequency	50/60 Hz ± 5 Hz
Max. imbalance operating voltage	± 3.0% of operating voltage
Effective power factor (λ)	0.9
cos φ	> 0.98
Switches on connection cable	2x / min
Max. short-circuit current	100000 A
Control voltage	24 V DC

Cable lengths
Maximum length of connection cable to hoist motor for shielded wiring	40 m
Maximum length of connection cable to hoist motor for non-shielded wiring	75 m
Maximum length of connection cable to hoist motor for shielded wiring and smoothing choke	100 m

For longer connection cables to the hoist motor (for example, for central contactor boxes), an output filter is connected between the frequency converter and the hoist motor.

Ambient conditions for operation
Protection class	IP 20
Relative humidity	5 % to 95 % (non-condensing)
Ambient temperature	0 °C to +45 °C
Maximum average temperature within 24 hours	40 °C
Maximum elevation above sea level	3000 m

If the temperature of the hoist panel regularly exceeds 60°C due to extreme ambient conditions, the hoist panel must also be cooled. Depending on the size of the hoist panel, a panel lid with fans or one or two heat exchangers can be installed.

Only with Siemens frequency converter

Frequency converter:

Electrical connection
Operating voltage	3 x 380 – 480 V ± 10 %
Network demand, network short circuit	≤ 1 %
Mains frequency	47 - 63 Hz
Effective power factor (λ)	0.9
Efficiency	95 - 97 %
Control factor	87 %
Control voltage	24 V DC

Cable lengths
Maximum length of connection cable to hoist motor for shielded wiring	25 m
Maximum length of connection cable to hoist motor for non-shielded wiring	100 m

For longer connection cables to the hoist motor (for example, for central contactor boxes), an output filter is connected between the frequency converter and the hoist motor.

Ambient conditions for operation
Protection class	IP 20
Relative humidity	< 95 % (non-condensing)
Ambient temperature	-10 - +50° C
Maximum elevation above sea level	Up to 1000 m above sea level without power reduction

Only with the Schneider frequency converter

Frequency converter:

Electrical connection
Operating voltage	380 ‒ 480 V -15 - +10 %
Mains frequency	50 ‒ 60 Hz +/- 5 %
Control voltage	24 V DC

Cable lengths
Maximum length of connection cable without smoothing choke	50 m
Maximum length of connection cable to hoist motor for shielded wiring	100 m
Maximum length of connection cable to hoist motor for non-shielded wiring	200 m

For longer connection cables to the hoist motor (for example, for central contactor boxes), an output filter is connected between the frequency converter and the hoist motor.

Ambient conditions for operation
Protection class	IP 20
Relative humidity	5 % ‒ 95 % (non-condensing)
Ambient temperature without power reduction	-15 ‒ 50° C
Ambient temperature with power reduction	50 – 60° C
Maximum elevation above sea level without power reduction	Up to 1000 m above sea level
Maximum elevation above sea level with power reduction	Up to 4800 m above sea level

Outputs
Rotational direction output (yellow)	Clockwise = positive signal Anti-clockwise = negative signal
Speed 1 output (grey)	2000 impulses/rotation
Speed 2 output (green)	1000 impulses/rotation (not used for ABULiner)
Speed 3 output (brown)	100 impulses/rotation (not used for ABULiner)

Ambient conditions for operation
Housing	Installation in a housing with IP 54 required
Relative humidity	5 % ‒ 85 %
Ambient temperature	-10° C ‒ 55° C

Electrical connection
Operating voltage	24 V
Current consumption	Max. 50 mA